Veneer Equipment
14 products. Displaying 1 to 10. « < 1 - 2 > »
Kuper / Josting Model No.: QFS-800
Open Front Cross Clipper
The Kuper / Josting QFS-800 open front cross clipper is designed for 180 degree access. This design concept allows for one-man operation as well as integrating the clipper with an "EFS" guillotine producing the perfect "work-cell". The QFS-800 is equipped with an "as-cut" light line, pressure bar, and a draw cutting motion of the knife.
Call (801)498-7891
Details: ** Open front design allows a 180 degree view of the cutting action ** Pressure bar precedes the knife operation to clamp the waviest of veneers ** Draw cutting action insures a clean cut ** "As-Cut" green light line insures precise cutting ** Measuring tapes embedded in work table ** Positive brake motor with spur gear drive ** "Two-Hand" safety control operation ** Safety guards.
Additional Info: Cutting width: 800mm (31.5") ** Insertion Height: 60mm (2.36") ** Maximum thickness of a single sheet: 2mm (0.078") ** Cycle time: 1.6 seconds ** Total connected load: 2.8 kW (3.7 HP) ** Operating voltage: 480/3/60
Kuper / Josting Model No.: QFS-850
High Production Cross Clipper
The Kuper / Josting QFS-850 is a heavy, robust cross clipper designed for the high production shop requiring the throughput of an inline clipping operation. The QFS-850 comes standard with an "As-Cut" green light line, pressure bar, and a heavy duty mechanical drive.
Call (801)498-7891
Details: ** Heavy Duty, Rigid construction ** Pressure bar precedes the knife operation to clamp the waviest of veneers ** Draw cutting action insures a clean cut ** "As-Cut" green light line insures precise cutting ** Measuring tapes embedded in work table ** Positive brake motor with spur gear drive ** "Two-Hand" safety control operation ** Safety guards.
Additional Info: Cutting width: 850mm (33.5") ** Insertion Height: 60mm (2.36") ** Maximum thickness of a single sheet: 3 mm (0.118") ** Cycle time: 1.6 seconds ** Total connected load: 3.5 kW (4.7 HP) ** Operating voltage: 480/3/60
Kuper / Josting Model No.: EFS
Single Knife Veneer Guillotine
The Kuper / Josting Single-Knife Guillotines are designed for jointing veneer packages quickly and efficiently. The "EFS" is equipped with a "second-cut" device, which virtually eliminates tear-out. In addition the onboard computer controller allows storage of 99 different part sizes for fast and accurate recall.
Call (801)498-7891
Details: * Produces quality joints thanks to the powerful drawing motion of the knife at an angle of 20 degrees ** Parallel fence positioned with high speed motor ** Strip cutting mode (minimum 3/4" width) ** Clearly visible "As-Cut" green guide light ** side alignment fence ** Broad pressure beam (~8") for pressing the waviest of veneers flat ** Second cut mode with hydraulic adjustment to offset the knife by 0.9 mm ** Powerful crank drive enables cross cutting of veneers.
Kuper / Josting Model No.: ZFS
Double Knife Veneer Guillotine
The Kuper / Josting ZFS double-knife guillotines are designed for high production shops or shops requiring perfectly parallel veneers for cross feed splicing. Utilizing top and a bottom knives that cut simultaneously, the ZFS produces perfectly parallel veneers with half the labor. The onboard computer control and laser optimizing system makes the ZFS the complete tool for jointing veneers.
Call (801)498-7891
Details: Features of the ZFS series machines include: Computerized controller for multi-function operation ** Produces quality joints thanks to the powerful drawing motion of the knife at an angle of 20 degrees ** Laser optimization system ** Simultaneous operation of top and bottom knives for increased production and perfectly parallel veneers ** 2 to 3 packs per minute cutting capacity ** Precise parallel screw system for table alignment ** Heavy duty, rugged design to absorb pressing and cutting forces ** Top and bottom knives are interchangeable ** Grinding allowance of knives of 30 mm (>1") ** Intermittent operating hydraulic system for lower noise level and less heat ** Extremely safe operation using a 6-light curtain, two hand push button operation, electric safety control system, and protective gratings at the rear ** The machine also cuts paper, foils, plastic and other materials.
Additional Info: Technical specifications: Maximum cutting lengths: 2810 mm (110"), 3210 mm (126"), 3810 mm (158") ** Insertion height: 80 mm (3") ** cutting range: 20 to 470 mm (0.787 to 18.50") ** Pressure beam - 3 hydraulic cylinders, 2 pressure stages ** bottom knife has 1 hydraulic cylinder ** Total connected load: 9.5 kW ** Operating voltage: 480/3/60 ** Compressed air: 1 CFM @ 80 PSI.
Kuper / Josting Model No.: FAZ-100
Veneer Waste Chopper
The Kuper / Josting FAZ-100 waste chopper reduces bulk veneer strips to a more useable size and volume. In most cases veneer strips will reduce by a factor of 50%. The resultant chip size is suitable for most wood fired boilers.
Call (801)498-7891
Details: ** Quiet' operates at less than 80dB ** Clean operation, produces almost no dust ** Low power consumption of 12 amps @ 480 V ** produces wood chips suitable for pnuematic conveying ** Ideal for producing boiler fuel.
Additional Info: Cutting width: 700 mm (27.55") ** Insertion height: 90 mm (3.54") ** Conveyor area: 2320 mm X 700 mm ( 91" X 27.55") ** Conveyor indexing range: 10 to 25 mm (0.39" to 1") ** Volume capacity: 3 to 4 Cu. meters / Hr (105 to 141 Cu. Ft /Hr.) ** Total connected load: 5.7 kW (7.6 HP) ** Operating voltage: 480/3/60.
Kuper Model No.: KHL/2
Double roll hand gluer for veneer repair
The Kuper KHL/2 is a hand held gluer designed to repair veneer and veneer faces. Utilizing Kuper glue thread technology, the KHL/2 allows for repairs to be made on the backside of veneer thus eliminating the necessity of removing tape with a sander.
Call (801)498-7891
Details: Operating voltage is 110/1/60. Weight is approximately 1 Kg. (2.2 Lbs). Available as a single spool machine (model KHL/1).
Kuper Model No.: HFZ-4
Hand Veneer Splicer
The Kuper HFZ/4 is designed for the needs of a small shop or craftsman. The unit applies a zigzag application of glue thread with a straight line motion. Due to the design of the pressure rollers ahead of the glue thread applicator, the veneer joint is tight and secure. The HFZ/4 utilizes standard Kuper K12 glue thread.
Call (801)498-7891
Details: Operating voltage: 110/1/60. Weight 1 Kg (2.2 Lbs.)
Kuper Model No.: FW / 630-S
Veneer splicer
The Kuper FW / 630S Zig-Zag splicer is designed to join veneers using Kuper glue thread. This thread is applied in a Zig-Zag fashion to insure a tight joint with strong adhesion and tear resistant quality even on wavy veneers.
Call (801)498-7891
Details: Throat Depth: 630 mm (24.80") ** Feed speed: 7 M/Min. (22 FPM) ** Veneer thickness: 0.4 mm to 2 mm ((0.015" to 0.079") ** Operating voltage: 120/1/60.
Additional Info: Portable - on casters ** 120 volt single phase operation ** uses standard Kuper K12 thread ** Produces a tight quality joint.
Kuper Model No.: FW-920
Veneer Splicer
The Kuper FW / 920 Zig-Zag splicer is a higher production machine. It is designed to joint veneers using a special Kuper glue thread. This thread is applied in a Zig-Zag fashion to insure a tight joint with strong adhesion and tear resistant quality even on wavy veneers.
Call (801)498-7891
Details: Throat Depth: 920 mm (36.22") ** Feed speed: 15 M/Min. (49 FPM) ** Veneer thickness: 0.4 mm to 2 mm ().015" to 0.079") ** Operating voltage 230 /3/60 or 480/3/60 ** Compressed air consumption is 1 CFM @ 80 PSI.
Kuper Model No.: FW/1150
Veneer Splicer
The Kuper FW / 1150 Zig-Zag splicer is a higher production machine. It is designed to joint veneers using a special Kuper glue thread. This thread is applied in a Zig-Zag fashion to insure a tight joint with strong adhesion and tear resistant quality even on wavy veneers. It Features a variable speed feed system. Choice of hot air or standard heating tube. Precise temperature controls. Thousands in use through out the world.
Call (801)498-7891
Details: Throat Depth: 1150 mm (45.27") ** Feed speed: 10 to 30 M/Min. (33 to 98 FPM) ** Veneer thickness: 0.4 mm to 3 mm ().015" to 0.118") ** Total connected load: 1.5 kW ** Operating voltage 230 /3/60 or 480/3/60 ** Compressed air consumption is 1 CFM @ 80 PSI.